This is a genuine Dana/Spicer spindle nut kit for most Dana 44 4X4 front axles in domestic trucks. This kit includes 1 inner nut with pin (21588X), 1 outer nut w/o pin (31139) and 1 washer with locking tab and holes (36569). This kit is for one side, so 2 kits are required per truck. 2 kits are also the same as Warn 33720 spindle nut kit, used to replace automatic locking hubs on Ford applications.
Dana 44 Spindle Nut Kit 4X4 Front Axle GM Ford Jeep International Dodge
$14.00
- SKU: 28068X
- Brand: Dana/Spicer
- Weight: .5
- Shipping: Calculated at checkout
Out of stock
Weight | .5 lbs |
---|---|
Dimensions | 6 × 4 × 2 in |
Be the first to review “Dana 44 Spindle Nut Kit 4X4 Front Axle GM Ford Jeep International Dodge”
You must be logged in to post a review.
Make | Model | Year |
---|---|---|
Ford | F150 | 1973 - 1974 |
Ford | F150 | 1975 - 1976 |
Ford | F150 | 1977 - 1978 |
Ford | F150 | 1979 - 1980 |
Ford | F150 | 1981 - 1982 |
Ford | F150 | 1983 - 1984 |
Ford | F150 | 1985 - 1986 |
Ford | F150 | 1987 - 1988 |
Ford | F150 | 1989 - 1990 |
Ford | F150 | 1991 - 1992 |
Ford | F150 | 1993 - 1994 |
Ford | F150 | 1995 - 1996 |
Ford | F150 | 1997 - 1998 |
Ford | F250 | 1973 - 1974 |
Ford | F250 | 1975 - 1976 |
Ford | F250 | 1977 - 1978 |
Ford | F250 | 1979 - 1980 |
Ford | F250 | 1981 - 1982 |
Ford | F250 | 1983 - 1984 |
Ford | F250 | 1985 - 1986 |
Ford | F250 | 1987 - 1988 |
Ford | F250 | 1989 - 1990 |
Ford | F250 | 1991 - 1992 |
Ford | F250 | 1993 - 1994 |
Ford | F250 | 1995 - 1996 |
Ford | F250 | 1997 - 1998 |
GM/Chevy | Blazer | |
GM/Chevy | K10 | |
GM/Chevy | K20 |
Related products
Axles & Axle Bearings
GM Ford Dodge Jeep Dana 44 4X4 Front Axle Cog Gear Slug 19 Spline Full Time Drive Flange
This is a genuine Dana/Spice cog or slug use to replace the lockout hubs on trucks with full time four wheel drive. This is 1.271″ 19 splines on the inside and 2.925″ 48 spline on the outside. These were used in many popular 1/2 and 3/4 ton applications.
View DetailsMiscellaneous
Dana 44 Corporate 10 Bolt 4X4 Front Axle Spindle Bolts Studs Steering Knuckle GM Ford Dodge Jeep
This is a genuine Dana/Spicer stud for the steering knuckle to the spindle.This fits Dana 44 and GM corporate 4X4 front axles. These are 3/8″-24 fine thread and the head of the stud is D shaped in order to clear the axle.
View DetailsThis is the upper nylon bushing in a Dana 60 4X4 front axle with the king pin setup. These were commonly found in GM, Ford, and Dodge applications from the early 1970’s to mid 1990’s.
View DetailsThis is a genuine Dana/Spicer 4X4 front spindle that fit’s the following Ford applications: DANA 44 SPINDLE WITH 5 HOLES. FITS MOST FORD 1977 1/2-1979 F250 . DOES NOT FIT 76-77 LARGE EXTERNAL HUB. BEARING JOURNALS – 2.5″ OUTER & 1.625″ INNER. FLANGE DIA- 6.12″ INNER BRG DIA 2.0” // LENGTH 6.25”
View DetailsThis is a genuine Dana/Spicer 4X4 spindle for the Dana 60 front axle in 1978-1998 Ford F350 trucks. This is the same as 700022, but is much cheaper. This includes the inner bearing, 2 dust seals, and axle thrust washer.
View DetailsThis is a genuine Dana/Spicer spindle that fits Ford F150 and Bronco 4X4 front applications from 1980-1992. This is for the Dana 44 front axle.
View DetailsThis is the upper screw in pin a Dana 60 4X4 front axle with the king pin setup. These were commonly found in GM, Ford, and Dodge applications from the early 1970’s to the early 1990’s.
View DetailsThis is the gasket for the 4 bolt cap that goes over the spring and bushing in a Dana 60 4X4 front axle with the king pin setup. These were commonly found in GM, Ford, and Dodge applications from the early 1970’s to the mid 1990’s.
View Details
Reviews
There are no reviews yet.