This is the gasket for the 4 bolt cap that goes over the spring and bushing in a Dana 60 4X4 front axle with the king pin setup. These were commonly found in GM, Ford, and Dodge applications from the early 1970’s to the mid 1990’s.
Dana 60 King Pin 4 Bolt Upper Cap Cover Gasket GM Chevy Ford Dodge 4X4 Front Axle
$0.75
- SKU: 37307
- Brand: Dana/Spicer
- Weight: 1.600000001411
- Shipping: Calculated at checkout
Weight | 1.600000001411 lbs |
---|---|
Dimensions | 6 × 4 × 2 in |
Be the first to review “Dana 60 King Pin 4 Bolt Upper Cap Cover Gasket GM Chevy Ford Dodge 4X4 Front Axle”
You must be logged in to post a review.
Make | Model | Year |
---|---|---|
Dodge Ram | W350 | 1973 - 1974 |
Dodge Ram | W350 | 1975 - 1976 |
Dodge Ram | W350 | 1977 - 1978 |
Dodge Ram | W350 | 1979 - 1980 |
Dodge Ram | W350 | 1981 - 1982 |
Dodge Ram | W350 | 1983 - 1984 |
Dodge Ram | W350 | 1985 - 1986 |
Dodge Ram | W350 | 1987 - 1988 |
Dodge Ram | W350 | 1989 - 1990 |
Dodge Ram | W350 | 1991 - 1992 |
Dodge Ram | W350 | 1993 |
GM/Chevy | K30 | 1973 - 1974 |
GM/Chevy | K30 | 1975 - 1976 |
GM/Chevy | K30 | 1977 - 1978 |
GM/Chevy | K30 | 1979 - 1980 |
GM/Chevy | K30 | 1981 - 1982 |
GM/Chevy | K30 | 1983 - 1984 |
GM/Chevy | K30 | 1985 - 1986 |
GM/Chevy | K30 | 1987 - 1988 |
GM/Chevy | K30 | 1989 - 1990 |
GM/Chevy | K30 | 1991 |
Related products
Axles & Axle Bearings
GM Ford Dodge Jeep Dana 44 4X4 Front Axle Cog Gear Slug 19 Spline Full Time Drive Flange
This is a genuine Dana/Spice cog or slug use to replace the lockout hubs on trucks with full time four wheel drive. This is 1.271″ 19 splines on the inside and 2.925″ 48 spline on the outside. These were used in many popular 1/2 and 3/4 ton applications.
View DetailsThis is a genuine Dana/Spicer spindle nut kit for most Dana 44 4X4 front axles in domestic trucks. This kit includes 1 inner nut with pin (21588X), 1 outer nut w/o pin (31139) and 1 washer with locking tab and holes (36569). This kit is for one side, so 2 kits are required per truck. [...]
View DetailsThis is the upper nylon bushing in a Dana 60 4X4 front axle with the king pin setup. These were commonly found in GM, Ford, and Dodge applications from the early 1970’s to mid 1990’s.
View DetailsThis is a genuine Dana Spicer spindle for the Dana 44 4X4 front axle in 1/2 and 3/4 ton trucks, Blazers, and Suburbans from 1973-1976. This is the same as part number 706528X, but it is much cheaper. This also comes with the dust seals, inner bearing, and plastic thrust washer.
View DetailsThis is a genuine Dana/Spicer 4X4 front spindle for Ford F350 trucks from 1978-1997 with the Dana 60 front axle. This kit includes the inner spindle bearing, thrust washer, and 2 rubber seals for the back side of the spindle.
View DetailsThis is a genuine Dana/Spicer 4X4 front spindle that fit’s the following Ford applications: DANA 44 SPINDLE WITH 5 HOLES. FITS MOST FORD 1977 1/2-1979 F250 . DOES NOT FIT 76-77 LARGE EXTERNAL HUB. BEARING JOURNALS – 2.5″ OUTER & 1.625″ INNER. FLANGE DIA- 6.12″ INNER BRG DIA 2.0” // LENGTH 6.25”
View DetailsTHIS IS A GENUINE DANA 44 SPINDLE WITH 5 HOLES FOR LARGE BEARING 1/2 TON DISC BRAKES APPLICATIONS. FITS MOST FORD 1976-1979 F150/F100 SERIES PICK UPS & SERVICE 1976-1978 BRONCO. THIS SPINDLE COMES WITH THE INNER BEARING, DUST SEALS, AND PLASTIC THRUST WASHER.
View DetailsThis is a lower king pin bearing and seal kit for a Dana 60 4X4 front axle with the king pin setup. These were commonly found in GM, Ford, and Dodge applications from the early 1970’s to the mid 1990’s. This kit does one side. 2 kits required per truck.
View Details
Reviews
There are no reviews yet.