This is a genuine Dana Spicer spindle for the Dana 44 4X4 front axle in 1/2 and 3/4 ton trucks, Blazers, and Suburbans from 1973-1976. This also comes with the dust seals, inner bearing, and plastic thrust washer.
1973-1976 GM Chevy Dana 44 4X4 Axle Front Spindle Blazer Suburban K10 K20
$210.00
- SKU: 706528X
- Brand: Dana/Spicer
- Weight: 5.0
- Shipping: Calculated at checkout
2 in stock
Weight | 5.0 lbs |
---|---|
Dimensions | 6 × 6 × 6 in |
Be the first to review “1973-1976 GM Chevy Dana 44 4X4 Axle Front Spindle Blazer Suburban K10 K20”
You must be logged in to post a review.
Make | Model | Year |
---|---|---|
GM/Chevy | Blazer | 1973 - 1974 |
GM/Chevy | Blazer | 1975 - 1976 |
GM/Chevy | K10 | 1973 - 1974 |
GM/Chevy | K10 | 1975 - 1976 |
GM/Chevy | K20 | 1973 - 1974 |
GM/Chevy | K20 | 1975 - 1976 |
Related products
This is a genuine Dana/Spicer 4X4 front spindle for Ford F350 trucks from 1978-1997 with the Dana 60 front axle. This kit includes the inner spindle bearing, thrust washer, and 2 rubber seals for the back side of the spindle.
View DetailsAxles & Axle Bearings
Spindle Nut Washer Rear Hub Dana 60 Spicer Dodge Jeep Ford Lock
This is a genuine Dana/Spicer spindle nut lock washer with folding tabs. These were used in the 1960’s and 1970’s on many common Dana applications, including Dana 60 and 70 front or rear axles. The I.D. is 1 13/16″. The O.D. is 2.375″ and they are 1/16″ thick. These are the same as Dorman part [...]
View DetailsAxles & Axle Bearings
DANA 60 FRONT 35 SPLINE CHROMOLY DRIVE FLANGES 4X4 Front Axle Chevy Ford Dodge
This is a genuine Dana/Spicer drive flange kit for a Dana 60 4X4 front axle with 35 spline outer axles. Most factory outer axles were 30 spline. These fit GM, Ford, and Dodge applications with 55 internal splines in the hubs.
View DetailsThis is the gasket for the 4 bolt cap that goes over the spring and bushing in a Dana 60 4X4 front axle with the king pin setup. These were commonly found in GM, Ford, and Dodge applications from the early 1970’s to the mid 1990’s.
View DetailsMiscellaneous
SPINDLE NUT ONE PIECE FORD DANA 44 IFS F150 F250 GM DODGE JEEP IHC RATCHETING HIGH SHEAR
New OEM One Piece Ratcheting Spindle Nut Used on 1980’s-1990’s Ford F150 and F250 IFS Dana 44 front axles. Will work in Chevy Dana 44 and corporate 10 Bolt Axles As well as Dodge Jeep and IHC Dana 30 and Dana 44 Front Spindles. Can be used to replace the 3 piece style of spindle nut kits. This [...]
View DetailsSmall Parts & Seals
DANA 44 SPINDLE BEARING & SEAL KIT BRONCO F150 1993-1996 FORD 4X4 FRONT AXLE
Dana 44 IFS BRONCO AND F150 1993-1996 Spindle Bearing and Seal Kit Includes 1 each Spindle Bearing (550759 or SCE2110) and V Seal, Wiper Seal (50492), and Thrust Washer (45651) as pictured.
View DetailsThis is a genuine Dana/Spicer 4X4 front spindle for the Dana 60 front axle found in 1980’s and early 1990’s GM and Dodge trucks. This kit includes inner spindle bearing, thrust washer, and the 2 rubber seals for the backside of the spindle. Photo shows spindle bearing installed, but they usually aren’t.
View DetailsMiscellaneous
Dana 44 Corporate 10 Bolt 4X4 Front Axle Spindle Bolts Studs Steering Knuckle GM Ford Dodge Jeep
This is a genuine Dana/Spicer stud for the steering knuckle to the spindle.This fits Dana 44 and GM corporate 4X4 front axles. These are 3/8″-24 fine thread and the head of the stud is D shaped in order to clear the axle.
View Details
Reviews
There are no reviews yet.