This is a genuine Dana/Spicer 4X4 spindle for the Dana 60 front axle in 1978-1998 Ford F350 trucks. This is the same as 700022, but is much cheaper. This includes the inner bearing, 2 dust seals, and axle thrust washer.
Dana 60 4X4 Front Spindle Ford F350 1978-1998
$75.00
- SKU: 10086724
- Brand: Dana/Spicer
- Weight: 10.0
- Shipping: Calculated at checkout
7 in stock
Weight | 10.0 lbs |
---|---|
Dimensions | 12 × 12 × 12 in |
Be the first to review “Dana 60 4X4 Front Spindle Ford F350 1978-1998”
You must be logged in to post a review.
Make | Model | Year |
---|---|---|
Ford | F350 | 1978 - 1979 |
Ford | F350 | 1980 - 1981 |
Ford | F350 | 1982 - 1983 |
Ford | F350 | 1984 - 1985 |
Ford | F350 | 1986 - 1987 |
Ford | F350 | 1988 - 1989 |
Ford | F350 | 1990 - 1991 |
Ford | F350 | 1992 - 1993 |
Ford | F350 | 1994 - 1995 |
Ford | F350 | 1996 - 1997 |
Ford | F350 | 1998 |
Related products
This is a spring seat that goes over the spring and bushing in a Dana 60 4X4 front axle with the king pin setup. These were commonly found in GM, Ford, and Dodge applications from the early 1970’s to the early 1990’s.
View DetailsThis is the upper screw in pin a Dana 60 4X4 front axle with the king pin setup. These were commonly found in GM, Ford, and Dodge applications from the early 1970’s to the early 1990’s.
View DetailsAxles & Axle Bearings
GM Ford Dodge Jeep Dana 44 4X4 Front Axle Cog Gear Slug 19 Spline Full Time Drive Flange
This is a genuine Dana/Spice cog or slug use to replace the lockout hubs on trucks with full time four wheel drive. This is 1.271″ 19 splines on the inside and 2.925″ 48 spline on the outside. These were used in many popular 1/2 and 3/4 ton applications.
View DetailsThis is a complete set of aftermarket spindle nuts and washers for a Dana 60 front axle. It consists of 2 each inner nut with pin, locking washer, and outer nut with the pin. These were commonly found on GM, Ford, and Dodge applications. They were also used on Dana 50 applications in Ford applications. [...]
View DetailsTHIS IS A GENUINE DANA 44 SPINDLE WITH 5 HOLES FOR LARGE BEARING 1/2 TON DISC BRAKES APPLICATIONS. FITS MOST FORD 1976-1979 F150/F100 SERIES PICK UPS & SERVICE 1976-1978 BRONCO. THIS SPINDLE COMES WITH THE INNER BEARING, DUST SEALS, AND PLASTIC THRUST WASHER.
View DetailsThis is the gasket for the 4 bolt cap that goes over the spring and bushing in a Dana 60 4X4 front axle with the king pin setup. These were commonly found in GM, Ford, and Dodge applications from the early 1970’s to the mid 1990’s.
View DetailsThis is a master king pin kit for the Dana 60 front ends from the early 1970’s to the mid 1990’s. These fit most domestic applicarions. Included parts are as follows: 2 706395X (lower kit) 2 620132 (Upper 4 bolt cap) 2 37307 (upper 4 bolt gasket) 2 620180 (upper spring seat) 2 41886 (upper [...]
View DetailsThis is a lower king pin bearing and seal kit for a Dana 60 4X4 front axle with the king pin setup. These were commonly found in GM, Ford, and Dodge applications from the early 1970’s to the mid 1990’s. This kit does one side. 2 kits required per truck.
View Details
Reviews
There are no reviews yet.